Gimbal System – Download

Firmware Update


G3 Gimbal Firmware

G2 Gimbal Firmware

Handheld Firmware


Update Introduction

V2.2 Update Feature2015.04.15
  • Correct Panoramic Mode shooting angle and quantity to 0, 2, 4, 6, 8, 10
  • Cancel G3 Roll Follow function whereas “Follow” icon still leave on the interface but not allowed to be activated.
  • Added handheld rig receiver option.

V2.1 Update Feature2015.02.05
  • Added option to activate/disable the 6 control functions of gimbal.
  • When gimbal is connected, PAN axis will automatically be set to lock mode if it’s in follow mode. This is done to facilitate the ease of setting gimbal parameters.  After completing the setup the gimbal will automatically revert back to follow mode.
  • If any abnormalities affects the gimbal initialization, or PAN axis experiences abnormal compensation due to external forces, gimbal will automatically re-initialize and return to center.
  • If there is any irregular Gimbal performance happened, just simply point down Gimbal TILT or switch on “Neutral Point Calibration” then the gimbal can automatically neutralize back to the center by itself.

V2.0 Update Feature2015.01.31
  • Added return to center function.
  • Added panoramic photo function.
  • For gimbal control with single RC transmitter of 8 channels or more, with enough channels available from the RC transmitter, each of the function can be configured to channel 9~14 through APS-M program interface: pan, tilt, roll, shutter trigger, return to center, panoramic photo.
  • Consolidated gimbal parameter adjustment method. Pilot only need to adjust the P gain, D gain, and Power for Tilt axis. Adjustments for Pan and Roll are rolled into advanced settings which does not need adjustment for basic function.
  • Support for Graupner receivers.
  • Program interface automatically recognizes G2/G3 gimbal type without manual selection.
  • Added reset to factory default values function in interface program.
  • Added gimbal offset adjustment for all 3 axis.
  • Supports hand held gimbal use.
  • Enabled manual control for follow mode.
  • Tilt travel angle can be adjusted through program interface (90 to 120 degrees).

Reminder
  • G3 Gimbal V2.2 must be used with APS-M V2.1
  • G3 Gimbal V2.1 must be used with APS-M V2.0
V2.2 Update Feature2015.05.29
  • Enhance Gimbal performance stability.
  • Reduce operating temperature of Gimbal control board and motor, also reduce the chance of video interference.

V2.1 Update Feature2015.04.15
  • G2 default value : PAN Power 90 ; ROLL Power 60
  • Cancel G2 ROLL Follow function whereas “Follow” icon still leave on the interface but not allowed to be activated.
  • Strengthen PAN motor holding power in G2 PAN Follow mode.
  • Add G2 PAN Endpoint Adjustment Function.
  • Smoothen G2 PAN control.

Reminder
  • G2 Gimbal V2.1 must be used with APS-M V2.1
V2.1 Updates 2015.04.23
  • Adjust some parameter default value.
  • Correct Panoramic Mode shooting angle and quantity number.
  • Added handheld rig receiver option.

V2.0 Updates 2015.02.09
  • Added BTH password reset function.
  • Added receiver option for Graupner HoTT SUMD.
  • Added factory default reset function.
  • Fix bug from some setup steps.
  • Added G2 Gimbal setup adjustment section.
  • Update parameter adjustment interface layout.
  • Added two flight modes: Panorama and Return to Center.

V1.1 Updates 2014.11.17
  • Fix the bug after the file is being deleted.
  • Revise the G2 & G3 gimbal icon.
  • Revise the parameter value diagram.
  • Added interface language for German & Korean.
  • Revise Gimbal website linkage.
  • Add warning notice when switching the receiver type.
V2.1 Updates 2015.10.03
  • Adjust some parameter default value.
  • Correct Panoramic Mode shooting angle and quantity number.
  • Added handheld rig receiver option.

V2.0 Updates 2015.02.09
  • Added BTH password reset function.
  • Added receiver option for Graupner HoTT SUMD.
  • Added factory default reset function.
  • Fix bug from some setup steps.
  • Added G2 Gimbal setup adjustment section.
  • Update parameter adjustment interface layout.
  • Added two flight modes: Panorama and Return to Center.

V1.1 Updates 2014.12.01
  • Added interface language for German & Japanese & Korean.
Update Feature2015.08.29
  • Support for Handheld rig function control.
  • Enhance gimbal control feature to fit with handheld rig photography.

Reminder
  • Suitable for Windows V2.2 & iOS V2.1 interface software.
  • You have to install the Microsoft .NET Framework 4.6. Click me

V2.1 Introduction

V2.0 Feature & Notice



Support Equipment

G3-GH Gimbal
G3-5D Gimbal
G2 Gimbal


System Requirement

  Windows

Windows 10(32/64-bit) / 8(32/64-bit) / 7(32/64-bit) / Vista(32-bit) / XP

*If you cannot setup the Gimbal Windows version, please check whether you have installed the Microsoft .NET Framework 4.
http://www.microsoft.com/
  IOS

iPhone 4s and higher preferred
iPod touch 5 and higher preferred / The new iPad /
iPad with Retina display/iPad Air / iPad mini /
iPad mini with Retina display
  Android

Android 4 and higher preferred