• Download
  • APS-M Multicopter Control Unit – Download

APS-M Multicopter Control Unit – Download

Firmware Update

Update Instruction

V2.2 Update Feature 2015.05.29
  • Mainly optimize Attitude and GPS flight performance to stabilize multicopter performance during aerial photography shooting.
  • OSD added 4:3 and 16:9 Screen Ratio setting.
  • Display APS-M real time information as below indications : Satellite Count, Positioning Status, Voltage, Attitude Angle, Flight Distance from HOME, Latitude/Longitude.

V2.1 Update Feature 2015.04.14
  • Added shift switch for Return Home, Failsafe Protection, Low Voltage Protection. When disengage auto return home command, APS-M will turn to Attitude mode.
  • The mode LED will be solid red and solid green when either Auto Return Home or Failsafe Protection or Low Voltage Protection function is activated.
  • Added OSD display for Auto Return Home, Failsafe Protection and Low Voltage Protection function.
  • When radio lost signal, APS-M will wait for 5 sec. then start auto return home function.
  • When engaging Auto Return Home/Failsafe Protection/Low Voltage Protection function, the aircraft will automatically rises up to 10M above Home Position and securely fly back to the home position.
  • Adjust the flying area for No Fly Zone - Beijing.

V2.0 Update Feature 2015.01.31
  • Added gimbal trigger control for photo/video in single RC transmitter mode.
  • Added gimbal return to center function in single RC transmitter mode.
  • Added gimbal panoramic photo function in single RC transmitter mode.
  • Added control for gimbal roll axis in single RC transmitter mode.
  • For single RC transmitter operation, channel 9 ~ 14 can be user configured to control gimbal functions (pan, tilt, roll, shutter trigger, return to center, panoramic photo).
  • Added Spektrum DSM2 satellite receiver support for up to 18 channels.
  • Support for Graupner receivers.
  • Support for i.BUS receiver system.
  • Bluetooth passcode can be set through smartphone app.
  • Selectable automatic return home heading (nose in or tail in).
  • PCU hibernation setting now defaults to OFF.
  • Added reset to factory default values function in interface program.
  • Softening of breaking action during flight to increase gimbal stability during filming.
  • Increased Automatic Return Home altitude to 10M, reduced flight speed to 3M, and softened descending rate.
  • Added PCU voltage calibration function.
  • Added no flight zone (Beijing)
  • Prevent activation of low voltage and loss of control automatic return home failsafe within 20M radius from home point.
  • Default low voltage threshold has been reduced to: 1st stage 3.625v, 2nd stage 3.60V.
  • Low voltage failsafe setting value has been adjusted.
  • Prevents switching into manual mode during automatic return home. System will force into GPS mode to prevent pilot from losing control in manual mode.

V1.1 Update Feature 2014.11.26
  • The main point for the system update: To shorten the time required for GPS positioning.

Reminder
  • Before updating the firmware, please remove the motor signal wire to ensure yourself and aircraft safety.
V2.2 Updates 2015.06.06
  • OSD added 4:3 and 16:9 Screen Ratio setting.
  • Display APS-M real time information as below indications : Satellite Count, Positioning Status, Voltage, Attitude Angle, Flight Distance from HOME, Latitude/Longitude.

V2.1 Updates 2015.04.23
  • System supporting feature modification.

V2.0 Updates 2015.02.09
  • Added BTH password reset function
  • Added receiver option for Graupner HoTT SUMD
  • Added factory default reset function
  • Fix bug from some setup steps
  • Added Gimbal Setup function
  • Added “OFF” option for Intelligent Flight mode
  • Added flight mode: Return HOME Heading Direction
  • Added PCU Voltage Calibration function

V1.1 Updates 2014.11.20
  • Fix the bug after the file is being deleted.
  • Added interface language for German ＆ Japanese ＆ Korean.
  • Revise APS-M website linkage.
V2.1 Updates 2015.10.03
  • OSD added 4:3 and 16:9 Screen Ratio setting.
  • Display APS-M real time information as below indications : Satellite Count, Positioning Status, Voltage, Attitude Angle, Flight Distance from HOME, Latitude/Longitude.

V2.0 Updates 2015.02.02
  • Added BTH password reset function
  • Added receiver option for Graupner HoTT SUMD
  • Added factory default reset function
  • Fix bug from some setup steps
  • Added Gimbal Setup function
  • Added “OFF” option for Intelligent Flight mode
  • Added flight mode: Return HOME Heading Direction
  • Added PCU Voltage Calibration function

V1.1 Updates 2014.12.01
  • Added interface language for German ＆ Japanese ＆ Korean.

Support Model

M690L
M480L
M470

System Requirement

  Windows

 Windows 10(32/64-bit) / 8(32/64-bit) / 7(32/64-bit) / Vista(32-bit) / XP

＊If you cannot setup the APS-M Windows version, please check whether you have installed the Microsoft .NET Framework 4.
＊The problem of installing APS-M in Win8.
It is the Win8’s limits of authority issue, please follow below steps to solve this problem:
1. Run CMD (Administrator)
2. Enter commands: msiexec /package "The route of the installation package"
http://www.microsoft.com/
  IOS

 iPhone 4s and higher preferred
  Android

 Android 4 and higher preferred